JTAGjet-C20000 is a small, palm-sized In-Circuit Debugger for the TMS320C2000 family of DSPs from Texas Instruments. It is equipped with a USB 2.0 port (USB 1.1 compatible) that runs in the high-speed mode at 480Mbps.

This emulator supports the following C2000 DSP devices:

TMS320F24x, TMS320LC240x, TMS320LF240x, TMS320C28xx, TMS320F28xx, TMS320F2801x, TMS320F2802x, TMS320F2803x, TMS320F2804x, TMS320F2823x, TMS320F2833x, TMS320C2834x, Piccolo and Delfino.

Compatible with Code Composer Studio. JTAGjet-C2000 is fully compatible with Code Composer Studio 3.x/4.x . It installs directly into the Code Composer Studio directories and becomes visible as JTAGjet Emulator in the CCS Setup utility with all preconfigured C2000 targets. Setting up to work with JTAGjet is just as easy as setting up a TI emulator – just drag and drop thepreconfigured target and emulator configuration and start CCStudio.

JTAG Chain Device Detection.  For custom made boards with more than one device on the JTAG chain,JTAGjet can detect all devices on the chain which is necessary into configure the CCS debugger.

Variable JTAG Clock.  JTAGjet-C2000 supports variable JTAG clock. It defaults to 10 MHz but may be set as low as 1 kHz (for slow FPGA prototypes or power saving devices) and up to 30 MHz to provide faster application downloads and quicker Flash programming.

Auto-Sensing Voltage.  JTAGjet-C2000 comes with a detachable, active JTAG probe to better accommodatelong scan chains and various JTAG pinout standards and low voltages. The standard probe comes with 14-pin  header and supports targets from 3V to 5V. A fully isolated JTAG probe is available as option.

Hardware Features       

•   USB 2.0 high-speed port (480 Mbps) provides faster downloads
•   Programmable JTAG clock from 1KHz to 15MHz       
•   Supports all on-chip breakpoints and RTDX
•   Powered by the USB port – no external power adapters needed      
•   3 LEDs provide status of target power, JTAG activity, PC host activity and emulator power.
•   Fully isolated, 14-pin JTAG probe
•   Made in USA

Software Features     

•  Supports Code Composer Studio 3.x and 4.x 
•  Change JTAG clock even when the CCStudio is running       
•  Detects and graphically shows all devices on the JTAG chain
•  Graphically monitors all pins on the JTAG header       
•  Windows 7 and XP compatible

ADA-ISO-TI14 is a fully isolated JTAG probe which reduces the chance of damage to the emulator associated with ground loops, voltage spikes, electrostatic discharge (ESD) and noise on power and ground lines generated by high-current motors and other machinery.

The probe can be powered from the target board (default) or from an external isolated 5V power supply (optional) if the target cannot deliver the extra 100mA needed by the probe.

Opto-isolator Features:
•  Supports all TMS320C2000, C5000, C6000, OMAP, DM and TMS470 / 570 devices
•  Operating JTAG voltage from 3.3V to 5V
•  Galvanic isolation up to 1000 V (peak)
•  50kV/μs transient immunity (typ.) on JTAG line
•  ESD protection of 8kV on contact and 15kV air discharge
•  Maximum JTAG clock rate up to 15MHz

Flasher -C2000

Flasher-C2000 is a software utility that enables Signum JTAGjet emulators to program the on-chip Flash memory of the Texas Instruments C2000 DSP family without  Code Composer Studio or special purpose software from other vendors.

Flasher -C2000 Features: 
•   Supports all C2000 Flash based devices       
•   GUI and batch driven interfaces
•   No CCStudio required   
•   Fast programming & erase algorithms       
•   Flash depletion recovery
•   Blank check
•   Save Flash to file
•   Flash security support


 

Data Sheet