The Stellaris® LM3S8930 microcontroller is based on the ARM® Cortex™-M3 controller core operating at 50 MHz, with 256 kB single-cycle flash, 64 kB single-cycle SRAM, 10/100 Ethernet MAC/PHY, 2 CAN controllers, a 24-bit Systick Timer, 4x 32-bit or 8x 16-bit general-purpose timers, a watchdog timer, a SSI / SPI controller, an I2C interface, a UART, a battery-backed hibernation module with RTC and 256 bytes of non-volatile state-saving memory, a low drop-out voltage regulator, brown-out reset, power-on reset controller, and up to 34 GPIOs.
Features
32-Bit RISC Performance
32-bit ARM® Cortex™-M3 v7M architecture optimized for small-footprint embedded applications
50-MHz operation
50-MHz operation with 32-bit ARM® Cortex™-M3 architecture
System timer (SysTick) provides a simple, 24-bit clear-on-write, decrementing, wrap-on-zero counter with a flexible control mechanism
Thumb®-compatible Thumb-2-only instruction set, with hardware-division and single-cycle-multiplication
Memory protection unit (MPU) provides a privileged mode for protected operating system functionality
Unaligned data access enables data to be efficiently packed into memory
Atomic bit manipulation (bit-banding) delivers maximum memory utilization and streamlined peripheral control
On-Chip Memory
256 KB single-cycle flash
User-managed flash block protection on a 2-KB block basis
User-managed flash data programming
User-defined and managed flash-protection block
64 KB single-cycle SRAM
Flexible Timer Capability
Four general-purpose timers, each configurable as one 32-bit or two 16-bit timers
Real-Time Clock (RTC) capability
24-bit system (SysTick) timer
32-bit watchdog timer
General-Purpose Timers
Four General-Purpose Timer Modules (GPTM), each of which provides two 16-bit timer/counters. Each GPTM can be configured to operate independently as timers or event counters (eight total) as a single 32-bit timer (four total), as one 32-bit Real-Time Clock (RTC) to event capture, or for Pulse Width Modulation (PWM)
32-bit Timer modes
Programmable one-shot timer
Programmable periodic timer
Real-Time Clock when using an external 32.768-KHz clock as the input
User-enabled stalling in periodic and one-shot mode when the controller asserts the CPU Halt flag during debug
16-bit Timer modes
General-purpose timer function with an 8-bit prescaler
Programmable one-shot timer
Programmable periodic timer
User-enabled stalling when the controller asserts CPU Halt flag during debug
16-bit Input Capture modes
Input edge count capture
Input edge time capture
16-bit PWM mode
Simple PWM mode with software-programmable output inversion of the PWM signal
Watchdog Timer
32-bit down counter with a programmable load register
Separate watchdog clock with an enable
Programmable interrupt generation logic with interrupt masking
Lock register protection from runaway software
Reset generation logic with an enable/disable
User-enabled stalling when the controller asserts the CPU Halt flag during debug
Controller Area Network (CAN)
Up to two CAN controllers supporting CAN protocol version 2.0 A/B
32 message objects, each with its own identifier mask
Bit rates up to 1Mb/s
Disable automatic retransmission mode for TTCAN
Maskable interrupt
Programmable loop-back mode for self-test operation
10/100 Ethernet Controller
Conforms to the IEEE 802.3-2002 Specification
IEEE 1588-2002 Precision Time Protocol (PTP) compliant
Full- and half-duplex for both 100 Mbps and 10 Mbps operation
Integrated 10/100 Mbps Transceiver (PHY)
Automatic MDI/MDI-X cross-over correction
Programmable MAC address
Power-saving and power-down modes
Serial Interfaces
Synchronous serial interface (SSI) with master and slave modes for SPI, MICROWIRE, or TI synchronous serial
I2C interface (master and slave)
Fully programmable 16C550-type UART with IrDA support
Synchronous Serial Interface (SSI)
Master or slave operation
Programmable clock bit rate and prescale
Separate transmit and receive FIFOs, 16 bits wide, 8 locations deep
Programmable interface operation for Freescale SPI, MICROWIRE, or Texas Instruments synchronous serial interfaces
Programmable data frame size from 4 to 16 bits
Internal loopback test mode for diagnostic/debug testing
UART
Fully programmable 16C550-type UART with IrDA support
Separate 16x8 transmit (TX) and 16x12 receive (RX) FIFOs to reduce CPU interrupt service loading
Programmable baud-rate generator with fractional divider
Programmable FIFO length, including 1-byte deep operation providing conventional double-buffered interface
FIFO trigger levels of 1/8, 1/4, 1/2, 3/4, and 7/8
Standard asynchronous communication bits for start, stop, and parity
False-start-bit detection
Line-break generation and detection
Inter-Integrated Circuit (I2C) Interface
Master and slave receive and transmit operation with transmission speed up to 100 Kbps in Standard mode and 400 Kbps in Fast mode
Interrupt generation
Master with arbitration and clock synchronization, multimaster support, and 7-bit addressing mode
GPIOs
13-34 GPIOs, depending on configuration
5-V-tolerant input/outputs
Programmable interrupt generation as either edge-triggered or level-sensitive
Fast toggle capable of a change every two clock cycles
Bit masking in both read and write operations through address lines
Programmable drive strength and slew-rate control
Programmable control for GPIO pad configuration:
Weak pull-up or pull-down resistors
2-mA, 4-mA, and 8-mA pad drive
Slew rate control for the 8-mA drive
Open drain enables
Digital input enables
Power
On-chip Low Drop-Out (LDO) voltage regulator, with programmable output user-adjustable from 2.25 V to 2.75 V
Battery-backed hibernation module with real-time clock and 256-bytes of non-volatile memory
3.3-V supply brown-out detection
Hibernation module handles the power-up/down 3.3 V sequencing and control for the core digital logic and analog circuits
Low-power options on controller: Sleep and Deep-sleep modes
Low-power options for peripherals: software controls shutdown of individual peripherals
User-enabled LDO unregulated voltage detection and automatic reset
3.3-V supply brown-out detection and reporting via interrupt or reset
Flexible Reset Sources
Power-on reset (POR)
Reset pin assertion
Brown-out (BOR) detector alerts to system power drops
